WHY WON’T MY TV CONNECT TO WIFI?
Most WiFi connection issues are caused by software issues within your TV, but often the cause is with the 2.4GHz/5GHz WiFi frequencies, IP lease expiration, or MAC address filtering.

You should start by trying to localize the problem to either your TV or your router and then you can follow the appropriate troubleshooting steps for each, which are detailed below, which apply to both Sharp Aquos and Sharp Roku TVs.

An important point to check is if other devices can connect to the Internet through your router, even if your TV cannot.

You can jump to the relevant steps in this guide, but I would recommend running through the steps in order to cover every base.

Is The Problem With Your TV or Router?

To help localize the problem to either your TV or your router, try setting up a hotspot on your phone and then connecting your TV to it.

Hotspots can be set up on iPhones from Personal Hotspot, and on Android from Settings -> Network and Internet -> Hotspot and Tethering.

• If your TV connects to your phone hotspot and can access the Internet through your phone, then you can assume that you have a problem with your router.
• If your TV will not connect to your hotspot, you have either a software issue with your TV or a hardware problem with the Wi-Fi card in your TV.

Depending on the results of the above test, you can then follow the router troubleshooting steps or TV troubleshooting steps as below. Check out the overview, then the detailed steps follow this.

---

Router Troubleshooting Steps Overview

Cause	Explanation
Incorrect Password	Double-check that the password for your router has been entered correctly on your TV and/or it hasn’t recently been changed by other members of your household.
MAC Address Filtering	Every router can filter which devices are allowed to connect to the Internet through their MAC addresses. If you have MAC address filtering on, your TV will connect to your router but will not get an active Internet connection.
Poor Signal	RF interference or too many devices on your WiFi network can prevent a solid connection.
Router Software Glitch	Try soft resetting your router and if that doesn’t help, then hard reset it.

---

TV Troubleshooting Steps Overview

Cause	Explanation
Software Glitch	If you have a newer model of TV like the Sharp Roku models, then WiFi connection problems can potentially be resolved by power cycling.
IP/DNS Conflict	If your TV is set to pull a manual IP/DNS, it can fail to be assigned an IP depending if the address range is outside one that your router provides. In this case, your TV may or may not connect to your phone’s hotspot.
Old Firmware	Constant disconnection problems might be resolved by updating firmware, if available.
2.4GHz/5GHz Bandwidth Issues	Even relatively recent TVs (2018 models) might not be able to connect to 5GHz WiFi and/or the bandwidth you are broadcasting on might have high levels of interference.
Incorrect Time/Date	IP addresses acquired by DHCP typically expire 24 hours – 1 week after assigning. If your TV’s date is outside this range, it can cause it to reject the IP address offered by your router/your router allow the connection.
WiFi Module Failure	If you have ruled out all software issues and potential router problems, then you are left with a WiFi module failure. Open up your TV and checks its connections are firmly seated first, then replace if necessary.

---

What To Do If Your Sharp TV Won’t Connect to WiFi

For a quick overview of the steps needed to fix your TV/router, you can take a look at my video below, with the full details for each step following this.

---

How to Fix Router WiFi Problems

---

1. Make Sure Your WiFi Password is Correct

If your WiFi will not connect at all on your TV, this could be a sign that the password you are entering is incorrect, or the WPS setup failed.

If you used WPS, try entering your password manually, and vice versa.

---

2. Check Your Router is Not Set for MAC Address Filtering

MAC address filtering allows you to specify which devices are allowed to connect to the Internet using their unique MAC addresses, which every Internet-capable device has.

If you, or someone in your family, has switched on MAC filtering at the router level, your TV will not connect to the Internet but it will still connect to your router.

So if you do have a connection to your router from your TV, but your TV has no Internet connection, then login to your router by typing the Admin IP address into your phone’s or computer’s browser. This is listed on a label on your router (usually 192.168.1.1 or similar), along with the admin login info.

Go to Advanced or Expert Settings and find MAC Filtering. Make sure this is turned off.

---

3. Possible WiFi Interference / Too Many Devices

If your Sharp TV is not detecting your home WiFi signal at all, then you need to make sure that your router is switched on and working properly, and that there is no interference or blocking of the WiFi signal between your router and TV.

If your TV won’t connect to the Internet but other devices will from the SAME location, then you can assume your router’s WiFi signal is good, and the problem is likely within your TV.

---

4. Sharp TV Not Picking Up 5GHz WiFi

Check the user manual for your specific TV to see which bandwidths it supports, but as an example, even some TVs from as late as 2018 only support 2.4GHz, meaning that if your router is only broadcasting a 5GHz signal, your TV cannot connect to it.

Older TVs might only accept 2.4GHz WiFi frequencies.

Login to your router’s landing page, usually found by typing 192.168.1.1 or 192.168.1.0 into a browser on your phone or computer (the exact IP will be on a label on your router).

Find the login info on your router’s label, and take a look at the overview page to see whether your TV is connecting on 2.4GHz or 5GHz.

If it is connecting on the 5GHz channel, try changing the settings in your TV’s Network Status page to connect only on 2.4GHz.

You can also update the channel frequencies in the router itself, usually found under Expert Settings or Advanced Settings, changing these values and retesting your TV’s Wi-Fi connection to see if they make any difference.

---

5. Reset Your Router

You can first try a soft reset of your router – unplugging it for 30 seconds – to see if that fixes your issue.

If not, try a hard reset of your router by pressing a paperclip or similar into the small reset hole usually found on the back of your router.

You will need to hold the paperclip on the reset button for at least ten seconds to be sure your router is fully reset.

Make sure you still have your WiFi default password before hard resetting.

---

How to Fix Sharp TV WiFi Problems

---

1. Power Cycle Your Sharp TV

Although this might seem a basic step, power cycling your TV is often the best way to fix your Sharp TV not connecting to the Internet.

About 30% of people who contact me either through email, YouTube, or who leave comments here, fix their problem with a power cycle.

To soft reset a Sharp TV:

1. Unplug your Sharp TV and hold down the physical power button beneath the IR receiver on the TV for at least 15 seconds.
2. Wait for at least 30 minutes for any residual power to drain.
3. Plug your TV back in and try switching it on. You should see a red light if you have been successful.
4. It’s a good idea to try this a couple more times if it doesn’t work at first, as this can sometimes take a few goes to kick in.

Make sure you do wait for the full 30 minutes before plugging your TV back in – you would be surprised how long the components within your TV can hold a charge, and you want to make sure it has fully reset.

If you have a Sharp Roku TV, then you can try clearing the cache.

On your remote, and with your TV switched on, restart your TV using the button combination: Home – press 5 times; Up Arrow – press once; Rewind – press 2 times; Fast Forward – press 2 times.

You can also run a system restart from the menu.

To restart a Sharp Roku TV:

1. Go to the Home screen.
2. Then Settings.
3. And System.
4. Then Power.
5. System restart.
6. And click Restart.

---

2. Sharp TV Not Connecting to WiFi Automatically

If your TV WiFi is not working, but it is working on other devices, then check for an issue with your TV’s IP and DNS addresses.

In most cases, your TV should be set up to automatically select an IP address from your router, and usually also automatically pulls a DNS address, which is used to resolve IP addresses that your TV connects to, creating the URL that you see in the address bar.

But it’s possible that IP address lookup might have been set to Manual, and your DNS settings might be conflicting between your TV and WiFi router.

To fix this, press Home on your remote, then go to Settings -> Network & Internet -> [Click on the Connected Network].

If the IP Setting Mode is set to Manual, then change it to DHCP and restart your TV. This will make your TV select an IP address automatically from your router.

If the IP Setting Mode is set to DHCP, then change it to Manual, and change the DNS Server to 8.8.8.8, which is one of Google’s DNS servers that we know definitely works.

Restart your TV and try your apps again.

---

3. Sharp Roku TV Not Connecting to Wifi

If you have a Sharp Roku TV that won’t connect to the Internet, then go through the Roku Platform Secret Menu to enable network pings.

This can prevent your Sharp Roku TV from connecting with the Roku servers and this prevents your TV from making an Internet connection. This is a common cause of the timed-out connection error.

To access the Roku Platform Secret Menu:

1. Open the Home screen.
2. On your remote, press the button combination: Home x5; Fast Forward x 1; Play x 1: Rewind x1; Play x 1; Fast Forward x 1.

You will then see the Roku Platform Secret Menu screen. You want to select System Operations Menu.

And choose Network Menu.

You then want to scroll up to Disable Network Pings and click on it to change it to Enable Network Pings.

You can then back out of the menus and re-try your connection from the Network menu. You might want to try power cycling your TV again if the WiFi connection doesn’t come on immediately.

---

4. Update Your TV’s Firmware

If your Sharp TV keeps disconnecting from WiFi, then updating the firmware is your best option.

Firmware updates will be in the Settings menu, with the exact position depending on the TV model that you have.

---

5. Check Your TV’s Time and Date

IP addresses assigned automatically over DHCP have a lease expiration time attached, and this is the most common cause if your Sharp TV shows a “Not connected to Internet” error message.

This time is typically 24 hours – 1 week, and after this time is up, the router reclaims the IP address and either assigns a new one to your TV or re-leases the old one.

If your TV’s time and date are wrong, it can cause the IP address to “expire” at the moment of assigning and prevent connection to the router.

Go into the Settings for your TV and manually update the date and time to today if it is not already showing this.

---

6. Factory Reset Your Sharp TV

If the problem is with your TV and no other fix has worked, try factory resetting as a final step before looking at hardware fixes.

Factory reset (reinstall TV) can be found within the Settings menu.

---

8. Use an Ethernet Cable

Finally, if you are still unable to get the WiFi working on your TV, you might have to resort to using an Ethernet cable.

A temporary Ethernet connection can help to ensure that firmware is up to date.

---

9. Replace the WiFi Module

If none of the previous steps have worked, then you are most likely suffering from a failed WiFi module which is pretty easy to replace yourself.

Take a look at the video below for a step-by-step guide to do this. You will need to open up your TV which will invalidate its warranty, so this is really only a solution for TVs that are over one year old.

Sharp TV Support and Warranty

It goes without saying that if your TV is under one year old, then you should contact Sharp customer support to get it replaced under warranty.

You can call Sharp directly at:

• 1-888-935-8880 (Mon – Sat, 10am – 9pm EST)

Even if Sharp won’t fix your TV, they might still offer you a discount on a future model if you pester them hard enough! This is always worth a try in my experience.

Sharp WiFi Troubleshooting Quick Tips

• Use your phone’s hotspot to localize the WiFi connection problem to either your TV or router.
• If your Sharp TV won’t connect to WiFi, then check the DHCP IP address is set to obtain automatically and that your TV’s date and time are correct.
• If the problem is with your router, check MAC address filtering is off and that it is broadcasting an appropriate 2.4GHz/5GHz signal.
• The most common cause of WiFi connection problems on Sharp TVs are software-related, or failures of the WiFi module.

Hopefully, you’ve now got your TV’s WiFi back up and running. If not, leave me a comment and I’ll see what more I can do to help.

Read More:

Sharp Roku TV remote not working?

Sharp Roku TV black screen fix

Sharp Roku TV turning ON and OFF?